Whirlpool GI15NDXTQ Support Question
Whirlpool GI15NDXTQ Support Question
Find answers below for this question about Whirlpool GI15NDXTQ - 15" 50 lb. Icemaker.Need a Whirlpool GI15NDXTQ manual? We have 2 online manuals for this item!
Question posted by nicole475 on May 29th, 2012
Why Is My New Icemaker Not Making Ice Or Cooling?
We had it cleaned as the light indicated it, but it still is not working. It is 3 years old
Current Answers
Related Whirlpool GI15NDXTQ Manual Pages
Use and Care Guide - Page 3
...using your appliance.
This is , tell you how to move and install ice maker. SAVE THESE INSTRUCTIONS
3 ICE MAKER SAFETY
Your safety and the safety of others .
We have provided ...Do not use an adapter. ■ Do not use an extension cord.
■ Disconnect power before cleaning. ■ Disconnect power before operating. ■ Use two or more people to reduce the chance of...
Use and Care Guide - Page 4
...
WARNING
Excessive Weight Hazard
Use two or more people to work properly.
Removing Packaging Materials
Remove tape and glue from the elements, such as shown. If needed, you remove all of the packaging materials, clean the inside of your ice maker before using it. Floor level
■ Choose a location where the floor is...
Use and Care Guide - Page 5
...important to make several adjustments to level it . Water Supply Requirements
A cold water supply with ice maker installations that have the proper electrical connection: A 115 Volt, 60 Hz., AC only, 15- Reverse..., 3 prong wall receptacle installed by the ice maker, is recommended. If you .
1.
IMPORTANT: If this is a built-in order to work properly. If you may occur, resulting in...
Use and Care Guide - Page 6
... is not level, repeat steps 2 to connect the copper tubing. Connect Water Supply
Read all directions before making the final connection to avoid possible water valve malfunction.
5. Tools needed . Be sure both ends of the ice maker.
6. Compression sleeve B.
Connecting the Water Line
1. Bulb B. Now you begin. Bend the copper tubing to...
Use and Care Guide - Page 7
...supply
line connector D. Thread the nut onto the end of 15.88 mm) inside the cabinet. Drain Connection
Gravity Drain System
Connect the ice maker drain to your drain in accordance with a 1¹...
A. Vent hose (drain pump models only) C. Remove and discard the short, black plastic tube from ice maker
8. NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet's side ...
Use and Care Guide - Page 8
....
8 Remove the hinge pin from the hinges and screw the top hinge pin back into position so that the drain system is required by your ice maker will not work. See "Drain Pump System."
3. D
C
B
A
A. For drain pump system connect the drain pump outlet hose to move and install...
Use and Care Guide - Page 9
... opposite side of the ice maker and tighten screws.
3. Hinge pin sleeve C. Hinge D. Do not use an adapter. Hex-head hinge screw B. Hinge pin sleeve C. Remove the "old" bottom hinge screws and... set aside. 2. Failure to follow these instructions can result in the top hinge hole on the new bottom hinge pin.
4. Hex-head hinge screw
A
Electrical Shock Hazard Plug into a grounded 3 ...
Use and Care Guide - Page 10
...:
■ If the water supply to be concerned about 5 minutes. Items stored on a daily basis. ICE MAKER USE
The Ice Making Process 1. Fresh water enters the machine for each freezing cycle.
4. How Your Ice Maker Works
When you first start the ice maker, you may hear water running from the evaporator plate to the water reservoir may...
Use and Care Guide - Page 11
... often as every 6 months. Use one bottle of 15 to 20 grains/gal. (4 to clean your ice maker. Fill the bottle twice with warm water and mild soap or detergent.
Drain cap
7. When the indicator light turns green (approximately 70 minutes), the cleaning cycle is needed. If the service light turns on again, call 1-800-807-6777...
Use and Care Guide - Page 12
...screws C. Condenser
A dirty or clogged condenser: ■ Obstructs proper airflow. ■ Reduces ice making capacity. ■ Causes higher than recommended operating temperatures
which may lead to remove the lower...cutter grid. Replace all parts and panels before cleaning. Lift the cutter grid up and out. WARNING
Interior Components
1. Unplug ice maker or disconnect power. 2. Remove the drain...
Use and Care Guide - Page 13
... thin ice or no control indicators are ...ice level sensor harness.
14. After cleaning, make sure that all remaining ice from water pan is securely in 1 gal. (3.8 L) warm water. Replace all ice from the drain line. To shut down the ice maker: 1. 9. Rinse in ice...machine.
13 Vacation and Moving Care
WARNING
A
B
A.
Check the following instructions.
■ Replace the ice...
Use and Care Guide - Page 14
...? Be sure that were removed from the water pan, and you should clean the ice maker. This is added once per ice-making process.
■ Is there a "whooshing" sound? Ice maker runs but produces no kinks in the line.
■ Is the service light flashing on .
■ Is the drain cap securely in the reservoir overflowing...
Use and Care Guide - Page 15
...correspondence.
15 For further...Make sure that you need to local dealers, repair parts distributors, and services companies.
See "Ice Maker System" in the "Cleaning" section.
■ Are there clumps of ice in the water supply?
Move the ice...new WHIRLPOOL® appliance.
FSP® replacement parts will help , follow the instructions below. This information will fit right and work...
Use and Care Guide - Page 16
...BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. If outside the 50 United States and Canada, contact your sales slip together for...with electrical or plumbing codes, or use of consumables or cleaning products not approved by the customer. Repairs to parts or ... appliance light bulbs, air filters or water filters. WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY
LIMITED WARRANTY
For one year from ...
Trim Kit Instructions - Page 1
...panel and trim on both sides and all edges of customers choice. Install new door handle supplied using the old mounting screws. Match woodgrain direction with
adhesive tape. 3. Sand panel edges to...NOTE: Customer Panel shown must be 3⁄4" (1.9 cm) thick and requires the following changes for Ice Maker Trim Kit - These changes must be made on door and mark the holes using eight (8) ...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Ice maker noises
... than they actually are normal. Side by the condenser fan. French Door with Ice bin in your ice maker. Water running from the flow of the ice maker can make a splashing sound. The ice maker is my ice maker noisy? Your new ice maker may make noises. Hard surfaces such as floors, walls and cabinets can also... -
My ice maker is making too much ice/won't stop making ice - Bottom freezer /French door refrigerator
... icemaker stop ice production when the ice bin is making ice - Bottom freezer/French door refrigerator No or low ice production - Find a local service provider: Product Category Washer or Dryer Refrigerator or Freezer Dishwasher Electric Range, Oven or Cooktop Gas Range, Oven or Cooktop Microwave Trash Compactor Window Air Conditioner Hot Water Dispenser Vent Hood Ice Machine Commercial... -
Too cold in fresh food compartment. French Door with ice bin in the door.
...Control Temperature Control, French Door with Ice Bin in the Door Food is being complete. If items in the fresh food section of your icemaker, ice is freezing in the crisper drawer ...supply to make ice without any water, which can make sure the ice maker is turned off the ice maker by side refrigerator If the ice maker is turned on the display panel, Then choose Ice Maker. ...
Similar Questions
Ice Maker Staying Cold But Not Producing Ice. Water Going To It And It Is On,
cleaned the entire unit however, it is not producing ice. water is running to it and the unit is on ...
cleaned the entire unit however, it is not producing ice. water is running to it and the unit is on ...
(Posted by llefeve47 12 years ago)
My Ice Maker Is Making Too Much Ice, I Think The Thermostat Might Be The Problem
(Posted by Anonymous-39136 12 years ago)
Ice Maker Has Service Light Blinking.
I have a whirlpool gi15nfrts ice maker. Two days ago it was making ice fine but it did not stop. It ...
I have a whirlpool gi15nfrts ice maker. Two days ago it was making ice fine but it did not stop. It ...
(Posted by Artusi 13 years ago)
