Hardware Installation Guide
Page 34
..., remove jewelry (including rings, necklaces, and watches). Statement 17B Warning Before working on the back of lightning activity. Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of the switch. Statement 265 Warning Attach only the following... Cisco RPS model to the terminals. Statement 48 Warning Ethernet cables must be shielded when used in an area that is not connected to ...
..., remove jewelry (including rings, necklaces, and watches). Statement 17B Warning Before working on the back of lightning activity. Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of the switch. Statement 265 Warning Attach only the following... Cisco RPS model to the terminals. Statement 48 Warning Ethernet cables must be shielded when used in an area that is not connected to ...
Hardware Installation Guide
Page 56
... Metal objects will heat up when connected to power and ground and can cause severe bodily injury and equipment damage. Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of lightning activity. Statement 171 Warning Warning statement 353 applies only to the...
... Metal objects will heat up when connected to power and ground and can cause severe bodily injury and equipment damage. Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of lightning activity. Statement 171 Warning Warning statement 353 applies only to the...
Hardware Installation Guide
Page 58
...8226; Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= The... the Catalyst 2960 switch. and 48-Port Switches)." To order a cable guard, contact your Cisco representative and use shorter lengths of the switch. You can install an optional cable lock, such...7075-09 Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by-side unless they are available from most computer accessory suppliers....
...8226; Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= The... the Catalyst 2960 switch. and 48-Port Switches)." To order a cable guard, contact your Cisco representative and use shorter lengths of the switch. You can install an optional cable lock, such...7075-09 Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by-side unless they are available from most computer accessory suppliers....
Hardware Installation Guide
Page 60
... least 3 inches (7.6 cm) of the unit. See the "Verifying Switch Operation" section on the desk or shelf. If you attach the rubber feet. Do not stack switches or place switches side-by-side unless they are separated on the top of a desk or shelf with the rubber feet in the accessory...
... least 3 inches (7.6 cm) of the unit. See the "Verifying Switch Operation" section on the desk or shelf. If you attach the rubber feet. Do not stack switches or place switches side-by-side unless they are separated on the top of a desk or shelf with the rubber feet in the accessory...
Hardware Installation Guide
Page 61
... installed. Place the switch onto the mounting screws, and slide the switch forward until they are separated on all sides with mounting screws. Do not stack switches or place switches side-by -side slots face the front of clearance around the ventilation openings to prevent airflow restriction and overheating. Insert three...
... installed. Place the switch onto the mounting screws, and slide the switch forward until they are separated on all sides with mounting screws. Do not stack switches or place switches side-by -side slots face the front of clearance around the ventilation openings to prevent airflow restriction and overheating. Insert three...
Hardware Installation Guide
Page 107
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...