Icom IC-F121S / F221S Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom IC-F121S / F221S manuals!
Problems with Icom IC-F121S / F221S?
Ask a Question
Free Icom IC-F121S / F221S manuals!
Problems with Icom IC-F121S / F221S?
Ask a Question
Popular Icom IC-F121S / F221S Manual Pages
Instruction Manual - Page 1
INSTRUCTION MANUAL
VHF TRANSCEIVER
iF111S iF121S
UHF TRANSCEIVER
iF211S iF221S
Instruction Manual - Page 2
... manual contains important operating instructions for long periods. NEVER connect the transceiver to rain, snow or any liquids. NEVER touch the transceiver (especially
the heat sink) when transmitting continuously for the IC-F111S/F121S VHF TRANSCEIVER and ICF211S/F221S UHF TRANSCEIVER. It will ruin the transceiver.
No risk of
Icom Incorporated (Japan) in an electric shock...
Instruction Manual - Page 3
...D User set mode ...SAFETY TRAINING INFORMATION 15
pressly approved by Icom Inc., could void your authority to ...replacement 13 I Channel selection 6
cle's engine. ronments.
ii Other microphones
have different pin assignments and may damage the transceiver.
tures below -22°F (-30°C) or above +140°F (+60°C), or in excessively dusty envi- I Optional OPC-617 installation...
Instruction Manual - Page 5
... LEDs blink, check the DC battery voltage is on
or off hook: - Sets to 'Audible' condition (unmute condition) when hook off . - Sets to 'Inaudible' condition (mute condition) when hook on . - tion. ➥ All LEDs blink while entering the power ON password. Automatic scan start when hook on . -
w TX/RX INDICATOR ➥ Lights red...
Instruction Manual - Page 6
... directly. CH DN
¡ BANK KEY BANK Select and determine a bank number.
¡ SCAN START/STOP KEY SCAN A Push this key for details concerning your Icom Dealer or System operator for 1 sec. Take the microphone off hook to [P0], [P1], [P2] and [P3] programmable function keys. Consult your transceiver's programming. 1 PANEL...
Instruction Manual - Page 7
...; WIDE/NARROW KEY W/N Push this key to toggle the bandwidth between wide or narrow.
¡ DTMF AUTODIAL KEY DTMF Push this key to send a 'reset code'. Ask your Dealer which call CAL A another station depending on the pre-setting. • Ask your system employs selective 'Individual/Group' calls.
Instruction Manual - Page 8
Push [P2] and [P3] to set mode. Provides higher communi- Please refer to p. 8. •Push and hold this key for 1 sec.
Do not install version #01, as they are not compatible. • Some PC board modifications are available. - UT-109: Non-rolling type. 32 codes are required when installing UT-109 and UT-110. 1 PANEL...
Instruction Manual - Page 9
...of channel selection are same.
AUTOMATIC SCAN TYPE: Channel setting is not necessary for password input: • The transceiver detects numbers in the ...Dealer. • The keys in the same block as directed by your system setup. e When all channel indicator LEDs still blink after inputting 4 digits, the input code number is programmed for a start over in sequence; KEY
0
1
2
3
...
Instruction Manual - Page 10
...pre-programmed period, the time-out timer is activated causing the transceiver to the trasceiver's setting; • Coded audio may be heard from the transceiver, then TX/RX
indicator turns green. • ... The channel is in mute condition. • Channel is busy. • A matched/non-matched CTCSS code is received. • The selected channel is a 'receive only' channel.
• Time-out timer...
Instruction Manual - Page 11
... UT-110 (#02) optional voice scrambler unit provides high performance private communication between stations with the same scrambler codes.
Entering the user set mode:
qWhile pushing and holding [P1] and [P2], push [POWER] to exit set the desired level/condition.
Please refer to select the item.
q Push and hold [P0]) again to
enter...
Instruction Manual - Page 13
NEVER connect to polarities.
I Supplied Accessories
q
w
ICOM
e r
t
KEY-STICKER
y
u
i
o
!0
!1
!2
q Microphone 1 w Microphone hanger and
screw set 1 set e Microphone hanger cable . 1 r DC power cable (OPC-1132)
1 t Function name stickers*
(KEY STICKER 1
y Mounting bracket 1 u Bracket bolts 4 i Mounting screws (M5×12) . 4 o Self-tapping screws (...
Instruction Manual - Page 14
... with your transceiver allows overhead mounting. • Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg. 3 CONNECTION AND MAINTENANCE
I Optional UT-108 installation
Install the optional UT-108 DTMF decoder unit as shown in the diagram below.
UT-108
Front panel
Spring washer
When using...
Instruction Manual - Page 16
... the source of the problem, if possible, and replace the damaged fuse with a new rated one. ❑ Fuse rating: 20 A, IC-F520/F620: 20 ...A
I Antenna
A key element in the supplied DC power cable. AVOID the use of any communication system is installed in the performance of solvents such as benzene or alcohol, as they may damage the transceiver surfaces. 13 I Fuse replacement...
Instruction Manual - Page 18
...Icom radio generates RF energy that are posted to be located outside of a vehicle and kept at a separation distance of 65 centimeters or more between the transmitter antenna of this device and persons during operation. 3. IC-F121S: The transmitter antenna is required to do so. IC-F221S...RF Exposure Requirements, the transmitter antenna installation shall comply with this may damage ...
Instruction Manual - Page 20
A-6199H-1EX Printed in Japan © 2002 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan Count on us!
Icom IC-F121S / F221S Reviews
We have not received any reviews for Icom yet.