Icom IC-F3161 / F4161 Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom IC-F3161 / F4161 manuals!
Problems with Icom IC-F3161 / F4161?
Ask a Question
Free Icom IC-F3161 / F4161 manuals!
Problems with Icom IC-F3161 / F4161?
Ask a Question
Popular Icom IC-F3161 / F4161 Manual Pages
Instruction Manual - Page 1
INSTRUCTION MANUAL
VHF TRANSCEIVER
iF3161T/S/DT/DS iF3163T/S
UHF TRANSCEIVER
iF4161T/S/DT/DS iF4163T/S
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
Instruction Manual - Page 2
....
This
instruction manual contains important operating instructions for the IC-F3161T/S/DT/DS, IC-F3163T/S VHF TRANSCEIVERS and IC-F4161T/S/DT/DS, IC-F4163T/S UHF TRANSCEIVERS.
See the operating guide for details...
READ ALL INSTRUCTIONS carefully and com-
Icom, Icom Inc. pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL - Equipment damage may occur.
Instruction Manual - Page 3
... exposed parts of
...any problems caused by Icom Inc.,...case of the transceiver's good performance and warranty. Changes or modifications to
operate this transceiver under FCC regulations. ii NEVER hold the transceiver so that
the antenna is vertical.
does not cover any accident caused when using non-Icom...accessories at high volume levels.
Icom optional equipment is water re-
Instruction Manual - Page 9
...)
8
i
T he keypad allows you to enter digits to:
9
• Select memory channels
• Select tone channels
10
u
• Select DTMF codes (during transmit)
• Set TX codes
11
• Start up with the password
12
i DEALER-PROGRAMMABLE KEYS [P0] to [P3] D esired function can be programmed by your dealer.
3
e
(p. 6)
!1
t PTT SWITCH [PTT]
4
r
Speaker
Push...
Instruction Manual - Page 10
....
!2 VOLUME CONTROL [VOL] R otate to turn the power ON/OFF and adjusts the audio level.
See p. 3 for details.
■ Function display
q w e r ty u i
o
CALA TXCU TXC SET !0
!1 BUSY/TRANSMIT INDICATOR ➥ L ights green while receiving a signal, or when the squelch is activated.
q SIGNAL STRENGTH INDICATOR Indicates relative signal strength level. 2 PANEL DESCRIPTION...
Instruction Manual - Page 11
... following explanations, the specific key is described using the 2 lines indication mode. Consult your Icom dealer or system operator for details con-
4
cerning your dealer for details. • In this key is not available.
➥ Push to select a transmit code channel after pushing and holding [Scan].
13
Set mode contents, DTMF code, etc.
➥ Push...
Instruction Manual - Page 12
...' and 'Cindy' are to select an operating zone. When [Rotary selector] selects "operating zone," this key while scan is paused (a signal is detected)
on the setting, the cleared channel is added to exit the scan group selection
mode. ➥ Push this key is "zone"?-
to indicate the scan list, then push...
Instruction Manual - Page 13
... Call A and Call B), [Moni(Audi)],
select the desired tone frequency/code setting with [CH Up] or [CH Down]. Se-
16
lect the desired RAN setting with [CH
15
Up] or [CH Down]. After the selection, push... to un-mute the channel (audio is finished to the mute condition ('Inaudible'
tone frequency/code setting with [CH Up] or [CH Down]. PANEL DESCRIPTION 2
MEMORY CH 1/2/3/4 KEYS "CH1...
Instruction Manual - Page 15
....
14
The compander function reduces noise components from the optional unit
10
voice scrambler function ON and OFF. PANEL DESCRIPTION 2
TX CODE CHANNEL SELECT KEY "TXC"
USER SET MODE KEY "SET"
1
Push to erase the selected ID's. Then set mode.
to 5 ID's are memorized. ➥ Push and hold for 1 sec. again to exit user...
Instruction Manual - Page 16
... and start up password,
input the digit codes as directed by your dealer for details.
11 D Battery type selection
The battery type must be used for password input depending on the pre-setting. Ask your dealer. • 10-keypad can be fully charged for password input. • The transceiver detects numbers in this case. w If the...
Instruction Manual - Page 18
... depending on the pre-setting. Receiving: q Rotate ... system is used, the call specific station(s) only and prevent unwanted stations...instructions.
• This may be carried out in sequence. *Depending on programming.
• Refer to pages 14 or 15 for selection. q Select the desired TX code channel or 2/5-tone code
according to avoid interference. Transmitting: Wait for accessory...
Instruction Manual - Page 21
...call , the transceiver performs transmis-
15
Please refer to p. 10 [User Set Mode] section for instructions regarding using a programmable key. gency call operation is recommended.
16
However, ....
10
• Available set mode functions are Backlight, LCD contrast, Beep, Beep Level, Ringer Level, SQL Level, AF Min Level,
■ Man Down Emergency Call
11
Mic Gain, VOX Gain*, VOX Delay...
Instruction Manual - Page 22
... OFF.
*When "0" is programmed, this case.
■ Automatic Key Lock function
■ Forced Narrow function
Depending on the pre-setting, the Forced Narrow function is turned ON or...the lock function is not available. 17
to the password required condition. Entering of the channel setting, the [Wide/Narrow] key operation, repeater setting, and PC control command. however, an optional ...
Instruction Manual - Page 23
...specified in areas
with Icom radios or Icom charger. Battery damage may...this
16
instruction manual.
• R DANGER! Use and charge only specified Icom battery
...temperatures may also degrade battery performance or shorten battery life.
6
packs with temperatures above +60˚C (+140˚F). If the battery gets wet, be visible on the
fire.
14
outside of the case...
Instruction Manual - Page 34
...case
The VS-1SC is a VOX/PTT unit for operation. • The VOX (Voice Operated Transmission) function starts trans-
w Enter user set...SET TXCU TXC CALA
VOX function is required for Icom handheld transceivers, and allows you speak into the multi-con- then, automatically returns to set...exit user set the desired level/condition. Features
➥ 9-pin Spring-plug type head SP/MIC plug ...
Icom IC-F3161 / F4161 Reviews
We have not received any reviews for Icom yet.