Icom IC-F3021 / F4021 Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom IC-F3021 / F4021 manuals!
Problems with Icom IC-F3021 / F4021?
Ask a Question
Free Icom IC-F3021 / F4021 manuals!
Problems with Icom IC-F3021 / F4021?
Ask a Question
Most Recent Icom IC-F3021 / F4021 Questions
Popular Icom IC-F3021 / F4021 Manual Pages
Mdc 1200 Compatible Models - Page 1
... 1200
Compatible Models
MDC 1200 signaling features
Phone : +44 (01227) 741741 Fax : +44 (01227) 741742 E-mail : [email protected] URL : http://www.icomuk.co.uk
6F No. 68, Sec. 1 Cheng-Teh Road, Taipei, Taiwan, R.O.C. All other countries. SPECIFICATIONS
VHF UHF Frequency range (VHF)
(UHF)
IC-F70DT/DS, IC-F70T/S
IC-F80DT/DS, IC-F80T/S
136...
Mdc 1200 Compatible Models - Page 2
...the radio automatically ceases sending out the signal, clearing the channel for IC-F3021 and IC-F5021...radio automatically transmits an emergency signal. Please see if a remote radio in trouble, the radio will revive a subscriber unit that transmitted the emergency call .
Allows a user to set... their current status. Store specific profiles such as in the... integrate Icom radios into your...
Instruction Manual - Page 2
... from the lips and the transceiver is very close to, or touching exposed parts of the bat-
The basic operations, transmission and reception of personal injury, fire or electric shock. No risk of the transceiver are registered trademarks of operation, or after being placed in . (5 to trans- Icom, Icom Inc.
SAVE THIS INSTRUCTION MANUAL -
Instruction Manual - Page 8
... on version) The keypad allows you to enter digits to: • Select memory channels • Select tone channels • Select DTMF codes (during transmit) • Set TX codes • Start up with the password
u DEALER-PROGRAMMABLE KEYS [P0] to [P3] Desired functions can be programmed independently by your dealer. (p. 7)
i FUNCTION DISPLAY (p. 6) Displays a variety of...
Instruction Manual - Page 11
...cancel scanning operation. desired group.
➥ Push to select the
Code CH Select]. Then
resumes scanning after pushing [TX
group, then push... time period. desired group. function depends on the Power ON Scan set-
What is turned OFF; The desired channels are assigned into a ... ON;
function keys.
ting. cerning your Icom dealer or system operator for 1 sec.
In...
Instruction Manual - Page 12
...-DIAL KEY Push to select the transmit output power temporarily or permanently, depending on the pre-setting. • Ask your dealer for the output power level for transceiver-to change the tone frequency/code setting. again to enter the DTMF channel selection mode. DTMF AUTODIAL KEY ➥Push to turn the talk around...
Instruction Manual - Page 13
... or a key is also available via the 'Power ON function.' PANEL DESCRIPTION 2
CALL KEYS
TX CODE CHANNEL UP/DOWN KEYS
Push to each key.
assigned to transmit a 2-tone. to enter user set mode. • During user set mode is pushed, etc.
OPT MOMENTARY KEYS Controls the output signal level of the optional ports...
Instruction Manual - Page 15
... [MR-CH 1] to [MR-CH 4] keys to your system set up. Scanning stops when receiving a call specific station(s) only
Push [CH Up] or [CH Down] to your System Operator's instructions.
channel, in the normal fashion.
q Select the desired TX code channel or 2-tone code according to select the desired operating
and prevent unwanted...
Instruction Manual - Page 16
... OPERATION
I Receiving and transmitting
NOTE: Transmitting without an antenna may not be necessary depending on the pre-setting.) -
w Push [CH Up] or [CH Down] to avoid interference. Transmitting: Wait for the channel.... Hold the microphone 5 to 10 cm (2 to 4 inches) from
your side.
• Coded audio may be heard from your mouth, then speak into the microphone at a normal voice level....
Instruction Manual - Page 18
... frequency inversion type is transmitted on the previously selected channel.
w Push [P0] several times to suit your preferences and operating style. e Rotate [VOL] to "USER SET MODE KEY." (p. 9)
I Scrambler function
The voice scrambler function provides private communication between stations. However, when no emergency channel is specified, the signal is...
Instruction Manual - Page 19
... call The Priority A channel is selected when transmitting a status call. BASIC OPERATION 3
3
15
Set the 'Move to PrioA CH' item as a killer ID, is received, the stun function is...;ed ID, set as 'Clear down signal is received/transmitted -
I Priority A channel selection
When one of the password via the keypad is received, the transceiver switches to the password required condition. ...
Instruction Manual - Page 20
...that is not specified in this instruction manual. Misuse can result. Only Icom battery packs are tested and approved for use a battery with Icom radios or Icom charger.
DO NOT expose the battery... DANGER!
R DANGER!
Do not use a wet battery. Use the battery only with Icom radios or Icom charger. 4 BATTERY CHARGING
I Caution
Misuse of Lithium-ion batteries may result in the ...
Instruction Manual - Page 21
...the transceiver) into contact with fluid from the radio after discharging.
The charger is not completely charged by the specified time, stop charging.
If any part of the body that comes into the charger if it... charging. WARNING! NEVER charge the battery pack in direct sunlight. Icom recommends charging the battery at +20˚C (+68˚F).
BATTERY CHARGING 4
WARNING!
Instruction Manual - Page 30
... energy during the W ARN ING course of employment by the manufacturer for use the Icom beltclips listed on page 24 when attaching the radio to your Icom radio complies with the following guidelines: C AU TIO N
• DO NOT operate the radio without a proper antenna attached, as "Occupational Use Only", meaning it must be exceeded.
This...
Instruction Manual - Page 31
...Icom radio generates RF energy that are sensitive to do so. DO NOT operate the transmitter in areas that can exercise control over their exposure.
8 SAFETY TRAINING INFORMATION
8
27 Occupational/Controlled Use The radio... with other devices or systems. To avoid such interference, turn off the radio in which persons are exposed as consequence of their employment provided those persons ...
Icom IC-F3021 / F4021 Reviews
We have not received any reviews for Icom yet.