Icom IC-F3001 / F4001 Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom IC-F3001 / F4001 manuals!
Problems with Icom IC-F3001 / F4001?
Ask a Question
Free Icom IC-F3001 / F4001 manuals!
Problems with Icom IC-F3001 / F4001?
Ask a Question
Popular Icom IC-F3001 / F4001 Manual Pages
Instruction Manual - Page 1
Limited functions only
INSTRUCTION MANUAL VHF TRANSCEIVERS
iF3000
Series
UHF TRANSCEIVERS
iF4000
Series
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. The photo shows the VHF transceiver.
Instruction Manual - Page 2
...No risk of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i This instruction
manual contains important operating instructions for the IC-F3001/ IC-F3003/IC-F3006/IC-F3008 VHF TRANSCEIVERS and the IC-F4001/IC-F4003/IC-F4006/IC-F4008 UHF TRANSCEIVERS. SAVE THIS INSTRUCTION MANUAL- CAUTION NOTE
DEFINITION...
Instruction Manual - Page 3
... expressly approved by Icom Inc., could void your authority to correct the interference at his own expense. FCC INFORMATION
• FOR CLASS A UNINTENTIONAL RADIATORS: This equipment has been tested and found to comply with the instruction manual, may cause harmful interference to radio communications.
ii CAUTION: Changes or modifications to this transceiver under FCC...
Instruction Manual - Page 5
...transceiver warranty does
not cover any problems caused by unauthorized modification.
However, once the transceiver has been dropped, dust-protection and splash resistance cannot be operate correctly, or show an indication in the case of long hours of operation, or after being placed in extremely cold areas. DO NOT use or place the transceiver...transceiver surfaces. KEEP the transceiver ...
Instruction Manual - Page 6
... OPERATION 12-22 ■ Turning power ON 12 ■ Channel selection 13 ■ Call procedure 14 ■ Receiving and transmitting 15 ■ Setting the microphone gain 18 ■ Setting the squelch level 19 ■ Output power level selection 20 ■ Priority A channel selection 20 ■ MDC 1200 system operation 20 ■ Emergency...
Instruction Manual - Page 15
... 3, 4
18
Push to directly select memory channel 1, 2, 3 or 4, if programmed. 19
Consult your transceiver's programming.
4
SCAN A
5
➥ Push to start and cancel the scanning operation. 2 PANEL DESCRIPTION... assigned to the [Upper] and [Lower] 2
programmable function keys.
3
Consult your Icom dealer or system operator for details concerning
your dealer for details.
20
8 The paused ...
Instruction Manual - Page 19
while holding [PTT], rotate [VOL] to turn the transceiv- q Set [ROTARY SELECTOR] to any [ROTARY SELECTOR] 11
channel other than Channel 16.
[VOL] 12
w R ... repeat the
steps until 1 beep is heard. 3 BASIC OPERATION
■ Turning power ON
1
Prior to using the transceiver for the first time, the battery pack must be fully charged for details.
12 Ask your battery type is selected. ...
Instruction Manual - Page 20
When turning the power ON, the transceiver automatically starts scanning. To select a desired operating channel, do one of the following. •...Power ON function (p. 20) is not necessary for this type. AUTOMATIC SCAN TYPE: Selecting a channel is turned ON, the transceiver does not start scanning at power ON.
13 Scanning stops when a call is received.
3 BASIC OPERATION
■ Channel ...
Instruction Manual - Page 25
...available, depending on 1 or 4, an
13
error beep sounds after push-
14
ing.
Therefore, you can determine the current level setting by the type 15
of beep that sounds....Set [ROTARY SELECTOR] to any channel other than Chan-
3
[ROTARY SELECTOR]
4
[VOL]
5
nel 16.
6
e While pushing and holding
[Lower], rotate [VOL] to suit your op- However, you can adjust it to turn the transceiver...
Instruction Manual - Page 26
... level (loose squelch).
• The adjustable range is set on the presetting. NOTE: This operation may not be available, depending on 0 or 9, an error beep sounds after pushing [Upper] or [Lower].
If the...[VOL]
any channel other than Chan- 3 BASIC OPERATION
■ Setting the squelch level
The squelch circuit mutes the received audio signal, depending on the signal strength. nel 16.
Instruction Manual - Page 28
A repeat emergency signal is transmitted on the presetting. If your transceiver is programmed for the specified time period.*
* Depending on the previously selected channel. IMPORTANT: It is recommended to set an emergency channel individually to cancel the emergency call, push and hold [Emergency] again before transmitting the call operation.
Ask your dealer for...
Instruction Manual - Page 33
... or is not specified in this instruction manual.
7
R DANGER! Never use the...battery only with the transceiver for 6
any part of these
10
...conditions occur, contact your eyes, blindness can result. If fluid from inside the battery gets in an induction heating cooker. NEVER put the battery in a microwave oven, high- 13
pressure container, or in your Icom...
Instruction Manual - Page 43
...BC-197 multi-charger
1
For rapid simultaneously charging of BC-197 chargers for the IC-F3000/ IC-F4000 series.
3
BC-197 Charger Type Chargeable Battery Charging time
4
With AD-120* With AD...FA-SC61VC/FA-SC61UC cut antennas
FA-SC61VC : 136-174 MHz FA-SC61UC : 380-520 MHz 36 There are installed in the BC- 6
197, depending on the 2
version. BP-265 Li-ion battery Approx. 2.5 hrs.
5...
Instruction Manual - Page 46
e W hile pushing and holding [Upper], turn the transceiver power OFF.
Ask your dealer for details.
39 6 OPTIONS
D Turning the VOX function ON or OFF
The VOX function can be available, depending on the presetting.
w Set [ROTARY SELECTOR] to switch the VOX function ON or OFF. • 1 beep sounds when the VOX function is...
Instruction Manual - Page 47
...] to turn the power OFF, then ON to 10 (maximum).
• A beep sounds after pushing [Upper] or [Lower].
14
If the level is set on 1 or 10, an error beep sounds after pushing.
Therefore, you can be adjusted from 1 (minimum) to 10
(maximum).
2
q C onnect the optional headset (HS-94, HS-95 or...
Icom IC-F3001 / F4001 Reviews
We have not received any reviews for Icom yet.