Icom IP730D Support and Manuals
Get Help and Manuals for this Icom item
Icom IP730D Videos
Promotion video of IP730D/IP740D
Duration: 3:00
Total Views: 1,724
Duration: 3:00
Total Views: 1,724
Popular Icom IP730D Manual Pages
Instructions boxed With The Transceiver - Page 1
... and completely before using this radio by the manufacturer or an antenna specifically authorized by the "General Population" in an insecure place to charge the battery beyond the specified time for "Occupational Use Only."
For Advanced features and instructions, see the INSTRUCTION MANUAL on the product, comply with the essential requirements of the Radio...
Instructions boxed With The Transceiver - Page 2
...Charging required : Battery exhausted
F
Blinks when the transceiver downloading a new firmware. zz Rotate [VOL] clockwise to the 12 o'clock position to ...245T DTMF SPEAKER MICROPHONE
(Not released, as of the service area, or cannot receive a control signal.
••...a cigarette lighter socket. LLIt may have some and green problems.
NOTE: ••The transceiver MUST be different, ...
Instruction Manual - Page 1
INSTRUCTION MANUAL
HYBRID IP TRANSCEIVER
IP730D IP740D
INTRODUCTION 1 ACCESSORIES 2 BEFORE USING 3 USING THE CELLULAR MODE 4 USING THE IDAS MODE 5 OTHER FUNCTIONS 6 SET MODE 7 FOR YOUR REFERENCE
Instruction Manual - Page 2
SAVE THIS INSTRUCTION MANUAL- and Icom logo are registered trademarks or trademarks of their respective holders. is a trademark of Icom Incorporated. AquaQuakeTM is under license. INTRODUCTION
Thank you for choosing this product should provide you with years of trouble-free operation. Icom, Icom Inc. All other products or brands are registered trademarks of Icom...
Instruction Manual - Page 7
... and waterproof protection only when the connector cover or the optional speaker microphone is open.
••Lights yellow: Receiving and transmitting in the Detailed Set mode (p. 6-5).
2-2 A loose connection will allow water intrusion into the connector. 2 BEFORE USING
Panel description
DDFront, top and side panels
Antenna Connector
[Emer]
Rotary Selector
[PTT...
Instruction Manual - Page 20
... selector, or push [▲] or [▼] to avoid interference.
2. While holding down [PTT], speak at your mouth, then speak at low power in the Detailed Set mode. A fter pushing [PTT], pause briefly before you can assign functions in the IDAS mode when using an optional BP-305 battery case and alkaline...
Instruction Manual - Page 21
... an encrypted call.
4-4
If a call containing a different ID is made on the same channel a user is made on the settings, not only RAN but also individual ID or group ID must match. LLWhen the Encryption function is ON, push [PTT] to...) is heard only when the call contains a matching Key ID and Encryption key. When a channel is set up with a RAN, the squelch will not hear the call.
Instruction Manual - Page 23
... that is also used by other appliances, or stop using a Bluetooth device near such devices, interference may not be usable, depending on the Notice Tone settings or "BT PTT Beep" setting in the Set mode.
5-2
Instruction Manual - Page 24
...LLPush [CLR/Lock] to turn ON the transceiver.
••The Set Mode is displayed. DDSettings for a Bluetooth device. See the Set mode section for 6 seconds.
••The indicator quickly blinks red... mode when its Bluetooth function
is ON, but no bluetooth device is entered in the Set mode.
Hold down [FUNC], rotate [VOL] to cancel searching. ••If found...
Instruction Manual - Page 25
...push [FUNC]. 4. Turn OFF the transceiver, if it is turned ON. 2. LLRelease [FUNC] when "SET MODE" is displayed. 3. Rotate Rotary Selector or push [▲] or [▼] to initialize the ...Unconnected
DDInitializing the Pairing lists
If you have problems with Bluetooth operation, initialize the pairing lists, as shown below. SET
Init BT Unit Clear
Initializing the Pairing list ...
Instruction Manual - Page 27
...the vertical position, or when the user moves the transceiver before the Reminder Timer set time expires, the Emergency mode is canceled. Past 45 degrees
Stationary Sensitivity
If moving... raises the transceiver back from the preset angle towards the vertical position before the Reminder Timer set time. Sends an Emergency call . AND ••The transceiver is detected as obstructions,...
Instruction Manual - Page 28
... following functions, depending on � Icom is not responsible for the ON Timer preset time�
L If a user pushes any key before the Reminder Timer set time expires, the Emergency mode is canceled�
Enters the Emergency mode. ON Timer
Reminder Timer
Emergency Timer
No motion is detected.
[PTT]
No operation...
Instruction Manual - Page 35
... transceiver continues transmitting after the user stops speaking, and then the VOX switches to your voice. Sets the internal microphone sensitivity. -12 dB ~ 12 dB (in the "VOX" item.
Ask your voice. Updates the transceiverʼs firmware.
DDCommon
Item LOG CLEAR FIRM UP
RX Notify Vol. Notify Vol. VOX
VOX Threshold*1 VOX Delay...
Instruction Manual - Page 39
...transmitted. ON or OFF
Sets the call or message...Sidetone" item. 6-7
Sets the call receive notification ...Sets the call Receive tone. Selects whether or not to a headset that indicates an individual call failed. 6 SET MODE
Set...Set mode. Ask your voice to output your dealer for "MSG"), 1, 3, 10, 20 (times)
Sets the call Initiation tone. Sets...Sets the number of -Area Warning ...
Instruction Manual - Page 52
... ••Loose connection of the service area. (" " blinks.)
- Remove the battery pack from the transceiver, or the transceiver is set too low.
- Attach the battery... it for repair. Charge the battery pack. (p. 7-5) ••The battery pack's over-discharge protection circuitry is displayed.)
- Restart the transceiver. 7 FOR YOUR REFERENCE
Troubleshooting
The following conditions...
Icom IP730D Reviews
We have not received any reviews for Icom yet.