Instruction Manual
Page 2
... WPA and WPA2 are registered trademarks of Wi-Fi Alliance. 2 TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY 7 THE CHEST HEART RATE MONITOR 13 HOW TO USE THE INCLINE TRAINER 14 HOW TO MOVE THE INCLINE TRAINER 26 MAINTENANCE AND TROUBLESHOOTING 27 EXERCISE..., call the telephone number on the front cover of Google LLC. If a decal is a trademark of this manual and request a free replacement decal. NORDICTRACK and IFIT are trademarks of ICON Health & Fitness, Inc. Apply the decal in the location shown.
... WPA and WPA2 are registered trademarks of Wi-Fi Alliance. 2 TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY 7 THE CHEST HEART RATE MONITOR 13 HOW TO USE THE INCLINE TRAINER 14 HOW TO MOVE THE INCLINE TRAINER 26 MAINTENANCE AND TROUBLESHOOTING 27 EXERCISE..., call the telephone number on the front cover of Google LLC. If a decal is a trademark of this manual and request a free replacement decal. NORDICTRACK and IFIT are trademarks of ICON Health & Fitness, Inc. Apply the decal in the location shown.
Instruction Manual
Page 4
... authorized ser- SAVE THESE INSTRUCTIONS 4 Never remove the motor hood unless instructed to raise, lower, or move the incline trainer until it is properly assembled. (See ASSEMBLY on page 7, and HOW TO MOVE THE INCLINE TRAINER on page 26.) You must be performed by an authorized service representative. If you feel faint...
... authorized ser- SAVE THESE INSTRUCTIONS 4 Never remove the motor hood unless instructed to raise, lower, or move the incline trainer until it is properly assembled. (See ASSEMBLY on page 7, and HOW TO MOVE THE INCLINE TRAINER on page 26.) You must be performed by an authorized service representative. If you feel faint...
Instruction Manual
Page 6
Note: If a part is not in parentheses below to see whether it is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity used for assembly. Extra parts may be included. 3/8" Star Washer (3)-12 5/16" x 3/4" Patch Screw (108)-4 #8 x 5/8" Machine Screw (106)-6 3/8" x 5 1/2" Screw (1)-4 6 PART IDENTIFICATION CHART Use the drawings below each drawing is preattached. The number in the hardware kit, check to identify small parts used for assembly.
Note: If a part is not in parentheses below to see whether it is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity used for assembly. Extra parts may be included. 3/8" Star Washer (3)-12 5/16" x 3/4" Patch Screw (108)-4 #8 x 5/8" Machine Screw (106)-6 3/8" x 5 1/2" Screw (1)-4 6 PART IDENTIFICATION CHART Use the drawings below each drawing is preattached. The number in the hardware kit, check to identify small parts used for assembly.
Instruction Manual
Page 7
...) 7 one Phillips screwdriver To avoid damaging parts, do not have internet access, call Customer Service (see page 6. • Place all assembly steps. • Assembly requires the following information to iconsupport.eu. ASSEMBLY • Assembly requires two persons. • To identify small parts, see the front cover of this manual). To register your product and... plastic sheet on the incline trainer, wipe it off with a soft cloth and a mild, non-abrasive cleaner. Do not dispose of the packing materials until assembly is normal. This is completed.
...) 7 one Phillips screwdriver To avoid damaging parts, do not have internet access, call Customer Service (see page 6. • Place all assembly steps. • Assembly requires the following information to iconsupport.eu. ASSEMBLY • Assembly requires two persons. • To identify small parts, see the front cover of this manual). To register your product and... plastic sheet on the incline trainer, wipe it off with a soft cloth and a mild, non-abrasive cleaner. Do not dispose of the packing materials until assembly is normal. This is completed.
Instruction Manual
Page 10
Attach the right handrail assembly (D) in the same way. 108 108 D 109 C 7. Do not overtighten the Machine Screws. 106 106 106 E 110 10 Attach the Push Bar Bottom 6 (109) with six #8 x 5/8" Machine Screws (106); Set the handrail assembly (E) on the floor in the position shown. start all six Machine Screws, and then tighten them. 6 Set the left handrail assembly (C) on the floor in the position shown. do not fully tighten the Patch Screws yet. Attach the Push Bar Top (110) 7 with two 5/16" x 3/4" Patch Screws (108);
Attach the right handrail assembly (D) in the same way. 108 108 D 109 C 7. Do not overtighten the Machine Screws. 106 106 106 E 110 10 Attach the Push Bar Bottom 6 (109) with six #8 x 5/8" Machine Screws (106); Set the handrail assembly (E) on the floor in the position shown. start all six Machine Screws, and then tighten them. 6 Set the left handrail assembly (C) on the floor in the position shown. do not fully tighten the Patch Screws yet. Attach the Push Bar Top (110) 7 with two 5/16" x 3/4" Patch Screws (108);
Instruction Manual
Page 11
... the Console (93) and the Console Base (92). Next, attach the handrail assembly (E) with four 3/8" x 5 1/2" Screws (1) and four 3/8" Star Washers (3) (only one side is shown); Then, tighten the four 5/16" x 3/4" Patch Screws (108) (only one side is shown). F ... Upright Cover until it snaps into place. Then, press the Right Outside Upright Cover (71) against the lower end of a second person, position the handrail assembly (E) below the Console (93) 8 as described above. Make sure that the wires (G) are no wires on the left side. start all four Screws, and then...
... the Console (93) and the Console Base (92). Next, attach the handrail assembly (E) with four 3/8" x 5 1/2" Screws (1) and four 3/8" Star Washers (3) (only one side is shown); Then, tighten the four 5/16" x 3/4" Patch Screws (108) (only one side is shown). F ... Upright Cover until it snaps into place. Then, press the Right Outside Upright Cover (71) against the lower end of a second person, position the handrail assembly (E) below the Console (93) 8 as described above. Make sure that the wires (G) are no wires on the left side. start all four Screws, and then...