Optoma TX763 Support and Manuals
Get Help and Manuals for this Optoma item
View All Support Options Below
Free Optoma TX763 manuals!
Problems with Optoma TX763?
Ask a Question
Free Optoma TX763 manuals!
Problems with Optoma TX763?
Ask a Question
Popular Optoma TX763 Manual Pages
User's Manual - Page 1
... Menus 23
How to operate ...23 Menu Tree...24 Image...25 Display ...29 Setup...32 Options...38
Appendices 41 Troubleshooting 41
Image Problems 41 Intermission Problems 44 Projector Status Indication 44 Remote Control Problems 46 Replacing the Lamp 47 Compatibility Modes 49 RS232 Commands 50 Ceiling Mount Installation 53 Optoma Global Offices 54 Regulation & Safety notices 56
English
User's Manual - Page 2
... Class B emissions limits
This Class B digital apparatus meets all servicing to qualified service personnel. Important Safety Instruction
1. Do not put the projector in accordance with the manufacturer's instructions :
A. Do not install near any ventilation openings. Please call Optoma to be referred to an authorized service center near water or moisture. WARNING: TO REDUCE THE RISK...
User's Manual - Page 3
... projector will not turn back on the remote control
and do not point the laser beam into the projector's lens when the lamp is in this may damage your local reseller or service center to the end of injury to the eyes, do not look into anyone's eyes. Usage Notice
Precautions
Please follow all replacement instructions...
User's Manual - Page 6
...Texas Instruments Single chip DLP® Technology NTSC/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and
HDTV compatible (480i/p, 576i/p, 720p, 1080i) Auto source detection with user definable settings Full ... Macintosh and PC compatible DVI-D support (HDCP compliant)
English Introduction
Product Features
This product is a XGA single chip 0.55" DLP® projector.
User's Manual - Page 17
... projector back on the projector's screen.
2. If the problem persists, you press "Power/Standby" button second, the system will show the timing countdown on the screen.
3. Installation
Powering off the projector lamp, you must wait until the projector has completed the cooling cycle and has entered standby mode. When you should contact your local dealer or our service...
User's Manual - Page 31
... / 1280 x 1024 /
1400 x 1050.
*All supported resolutions are : 720 x 400 / 854 x 480 / 1280 x 720 / 1280 x 768.
Normal: If your PC output is only supported under RGB source. Zoom
Press the to magnify...projector unit is used with a PC signal, either via an Analog or Digital connector.
Wide: If your PC output is a Normal (4:3) resolution you
must select this setting...
User's Manual - Page 33
...-Ceiling
When you can project behind a translucent screen with ceiling mounted projection. Mute Choose the "On" to turn mute on the display screen.
User Controls
Setup
Projection
Front-Desktop
The factory default setting.
Rear-Desktop
When you select this function, the projector reverses the
image so you select this function, the...
User's Manual - Page 36
... to switch on the projector.
Off: Choose "Off" to be requested to enter your password again. User Controls
Setup | Security
Security On: Choose "On" to use security verification when
the turning on the
projector without password verification.
Security Timer
Can be select the time (Month/Day/Hour) function to set the number of hours...
User's Manual - Page 41
... broken. Check if the projection lamp has been securely installed. Select the "Settings" tab.
(*) The resolution XGA (1024 x 768) is recommended for details)
Image Problems
No image appears on . Please
refer to the "Replacing the lamp" section.
Make sure you have opened the lens door and the projector is lower than or equal to...
User's Manual - Page 42
...with the projector.
Appendices
(*) The resolution XGA (1024 x 768) is in use. Next, select "Standard monitor types" under the "Models" box.
8. Press the toggle output settings.
First,...adjust resolution of your computer's manual for more information. Change the monitor color setting on "Show all equipment including the projector. Refer to your graphic card to make it...
User's Manual - Page 43
... 16:9 DVD, the projector will also need to adjust the aspect ratio by referring to the following:
Please setup the display format as 4:3 in 16:9 format on projector side. If the image is between the required dis- See page 19. tance 3.9 to 39.4 feet (1.2 to "Display Format" and try the different settings.
User's Manual - Page 47
...: To reduce the risk of projector." Appendices
Replacing the lamp
The projector automatically detects the lamp life. Warning: Lamp compartment may shatter and cause injury if it to change the lamp as soon as possible. The bulb may be used to wear safety glasses if changing the bulb when ceiling mounted. Make sure the projector has been cooled down before changing...
User's Manual - Page 48
Allow the projector to remove the 2 screws from the lamp module. 7. English 48 Disconnect the power cord. 4. Remove the lamp module. To replace the lamp module, reverse the previous steps. 9. Lamp Reset: (i)Press "Menu" (ii)Select "Options" (iii)Select
"Lamp settings" (iv)Select "Lamp reset (v)Select "Yes". Use a screwdriver ...
User's Manual - Page 53
To prevent damaging your projector, please use a third party ceiling mount kit, please ensure the screws used to attached a mount to use Optoma's recommended mount package for installation.
2. If you wish to the projector met the following specifications:
Please note that there is at least 10cm distance between the bottom cover of heat such as air-conditioning units...
User's Manual - Page 54
...
Fax : +33 1 41 46 94 35
92100 Boulogne Billancourt, France Service : savoptoma@optoma.fr
Optoma Spain
Paseo de la Castellana
135 7 Planta
Madrid, Spain
Tel.: +34...Service : info@optoma.no
Latin America
715 Sycamore Drive
Milpitas, CA 95035, USA 54 www.optoma.com.br
Tel : 408-383-3700 Fax : 408-383-3702 www.optoma.com.mx
Appendices
English
Optoma Global Offices
For service or support...
Optoma TX763 Reviews
We have not received any reviews for Optoma yet.