Operater's Manual
Page 12
...engaged, AND • Ground speed levers are not locked in their START/ PARK positions. CHECK MOWER BLADE STOPPING TIME The mower blades and mower drive belt should come to bypass or tamper with a Safety Interlock System. ENGINE SHOULD NOT CRANK IF: Decal, Ground Speed Lever, L.H. ENGINE SHOULD CRANK IF... seat with ground speed levers not locked in their START/PARK positions in their START/PARK positions. Decal, Weight Limit Part No. 7101940 12 www.Snapper.com Part No. 7104226 Decal, Ground Speed Lever, R.H. TEST 4 - Part No. 7104231 If the unit does not pass a safety test, do not...
...engaged, AND • Ground speed levers are not locked in their START/ PARK positions. CHECK MOWER BLADE STOPPING TIME The mower blades and mower drive belt should come to bypass or tamper with a Safety Interlock System. ENGINE SHOULD NOT CRANK IF: Decal, Ground Speed Lever, L.H. ENGINE SHOULD CRANK IF... seat with ground speed levers not locked in their START/PARK positions in their START/PARK positions. Decal, Weight Limit Part No. 7101940 12 www.Snapper.com Part No. 7104226 Decal, Ground Speed Lever, R.H. TEST 4 - Part No. 7104231 If the unit does not pass a safety test, do not...
Operater's Manual
Page 24
The slot in the direction indicated by the arrow, and remove the mower belt from under each end of the mower deck, then lower the mower deck to its lowest position. B Mower Removal and Installation NOTE: Perform mower installation ... front lift rods (C), and pull the rods out from the holes in the bracket. Removal 1. Place a 2 x 4 or similiar support under the unit. 24 www.Snapper.com Mower Belt Routing ep 4. Retain all moving parts to the rear R lift arms (C), and pull the arms out from the holes in the brackets. Adjustments and...
The slot in the direction indicated by the arrow, and remove the mower belt from under each end of the mower deck, then lower the mower deck to its lowest position. B Mower Removal and Installation NOTE: Perform mower installation ... front lift rods (C), and pull the rods out from the holes in the bracket. Removal 1. Place a 2 x 4 or similiar support under the unit. 24 www.Snapper.com Mower Belt Routing ep 4. Retain all moving parts to the rear R lift arms (C), and pull the arms out from the holes in the brackets. Adjustments and...
Operater's Manual
Page 25
... Lift Components (Right side shown, left side same) 25 Adjustments and Service Installation 1. Figure 17. Lower the mower deck to stop. 2. r n Important: Be sure the belt is installed properly onto all moving parts to its lowest position (see C Cutting Height Adjustment). Pull back on the tensioning idler (D, Figure 16) in the...
... Lift Components (Right side shown, left side same) 25 Adjustments and Service Installation 1. Figure 17. Lower the mower deck to stop. 2. r n Important: Be sure the belt is installed properly onto all moving parts to its lowest position (see C Cutting Height Adjustment). Pull back on the tensioning idler (D, Figure 16) in the...
Operater's Manual
Page 26
...adjustment after the initial 25 hour break-in p Figure 20. o u 2. e 4. This is turned off . 26 www.Snapper.com The mower blades and mower drive belt should come to dimensional variations on level ground. Remove key from ignition switch and disconnect spark plug wires to stop within 5 seconds... PTO switch is due to a complete stop . 3. o 3. Engage the PTO and wait several seconds. Check the windows for the mower drive belt to prevent the possibility of mower deck. Adjust PTO Clutch B A Figure 19. Note the position of tension when the gauge is being adjusted....
...adjustment after the initial 25 hour break-in p Figure 20. o u 2. e 4. This is turned off . 26 www.Snapper.com The mower blades and mower drive belt should come to dimensional variations on level ground. Remove key from ignition switch and disconnect spark plug wires to stop within 5 seconds... PTO switch is due to a complete stop . 3. o 3. Engage the PTO and wait several seconds. Check the windows for the mower drive belt to prevent the possibility of mower deck. Adjust PTO Clutch B A Figure 19. Note the position of tension when the gauge is being adjusted....
Operater's Manual
Page 29
... lever pivot points • discharge chute hinge • deck lift pivot points ot uc Generally, all greases are not installed. Keep oil and grease N d off belts and pulleys. Remember to moving metal parts should be oiled where contact is made with other parts. Figure 29. Disassemble parts to apply grease to...
... lever pivot points • discharge chute hinge • deck lift pivot points ot uc Generally, all greases are not installed. Keep oil and grease N d off belts and pulleys. Remember to moving metal parts should be oiled where contact is made with other parts. Figure 29. Disassemble parts to apply grease to...
Operater's Manual
Page 31
... service dealer. Dirty air filter. Engine choke control is not fully released. Engine runs, but rider will not turnover or start. Drive belt slips. Brake is in closed (if equipped). Internal transmission problem. Out of fuel. Drain fuel and replace with fresh fuel. c Circuit...or replace. (See engine manual.) Replace fuel filter. See engine manual. Too much oil in fuel. Unlock roll release rod(s). Belt is black. Fuel valve closed position. Battery terminals require cleaning. Battery discharged or dead. pr Engine knocks. Check/add oil as...
... service dealer. Dirty air filter. Engine choke control is not fully released. Engine runs, but rider will not turnover or start. Drive belt slips. Brake is in closed (if equipped). Internal transmission problem. Out of fuel. Drain fuel and replace with fresh fuel. c Circuit...or replace. (See engine manual.) Replace fuel filter. See engine manual. Too much oil in fuel. Unlock roll release rod(s). Belt is black. Fuel valve closed position. Battery terminals require cleaning. Battery discharged or dead. pr Engine knocks. Check/add oil as...
Operater's Manual
Page 32
... mower vibration. Mower blades, spindles, or pulleys are bent. See authorized service dealer. See authorized service dealer. Mower drive belt broken. Clean as required. Troubleshooting the Mower PROBLEM Mower will not hold. See engine speed control to drive. See Servicing the... Mower Blades. Mower drive belt slips or fails to FAST. See authorized service dealer. 32 www.Snapper.com Troubleshooting PROBLEM Rider drive belt slips. See authorized service dealer. p Ground speed too fast. See Servicing ...
... mower vibration. Mower blades, spindles, or pulleys are bent. See authorized service dealer. See authorized service dealer. Mower drive belt broken. Clean as required. Troubleshooting the Mower PROBLEM Mower will not hold. See engine speed control to drive. See Servicing the... Mower Blades. Mower drive belt slips or fails to FAST. See authorized service dealer. 32 www.Snapper.com Troubleshooting PROBLEM Rider drive belt slips. See authorized service dealer. p Ground speed too fast. See Servicing ...