Operater's Manual
Page 12
...parking brake disenaged, OR • Operator rises off seat with the switches/ devices. 7104226 7104227 TEST 1 - TEST 4 - If mower drive belt does not stop within five seconds, see your dealer. Part No. 7104226 Decal, Ground Speed Lever, R.H. ENGINE SHOULD CRANK IF:... Decal, Weight Limit Part No. 7101940 12 www.Snapper.com TEST 2 - Part No. 7104232 7104233 Decal, Control Panel, R.H. ENGINE SHOULD NOT CRANK IF: Decal, Ground Speed Lever, L.H. CHECK MOWER BLADE STOPPING TIME The mower blades and mower drive belt should come to a complete stop within five seconds after...
...parking brake disenaged, OR • Operator rises off seat with the switches/ devices. 7104226 7104227 TEST 1 - TEST 4 - If mower drive belt does not stop within five seconds, see your dealer. Part No. 7104226 Decal, Ground Speed Lever, R.H. ENGINE SHOULD CRANK IF:... Decal, Weight Limit Part No. 7101940 12 www.Snapper.com TEST 2 - Part No. 7104232 7104233 Decal, Control Panel, R.H. ENGINE SHOULD NOT CRANK IF: Decal, Ground Speed Lever, L.H. CHECK MOWER BLADE STOPPING TIME The mower blades and mower drive belt should come to a complete stop within five seconds after...
Operater's Manual
Page 24
... in the direction indicated by the arrow, and remove the mower belt from under each end of the mower deck, then lower the mower deck to raise the mower deck. Pivot the front wheels out of the mower deck. Mower Belt Routing ep 4. To adjust cutting height: Press the adjustment... (B) indicates the cutting height of the way and slide the mower deck out from the PTO pulley (C). The cutting height is adjustable between 1-1/2" (3,8 cm) and 3-3/4" (9,5 cm). Place a 2 x 4 or similiar support under the unit. 24 www.Snapper.com Cutting Height Adjustment E D for all removed hardware. 6....
... in the direction indicated by the arrow, and remove the mower belt from under each end of the mower deck, then lower the mower deck to raise the mower deck. Pivot the front wheels out of the mower deck. Mower Belt Routing ep 4. To adjust cutting height: Press the adjustment... (B) indicates the cutting height of the way and slide the mower deck out from the PTO pulley (C). The cutting height is adjustable between 1-1/2" (3,8 cm) and 3-3/4" (9,5 cm). Place a 2 x 4 or similiar support under the unit. 24 www.Snapper.com Cutting Height Adjustment E D for all removed hardware. 6....
Operater's Manual
Page 25
...tensioning idler (D, Figure 16) in the direction indicated, and install the belt onto the PTO pulley as shown in the rear mower deck brackets (B), and secure each end of the way and slide the mower deck under each with a washer and hairpin clip (A). A tions,... side shown, left side same) 5. r n Important: Be sure the belt is installed properly onto all moving parts to its lowest position (see C Cutting Height Adjustment). B 3. t fo ctioC A B o u Figure 18. Lower the mower deck to stop. 2. Adjustments and Service Installation 1. Insert the rear lift ...
...tensioning idler (D, Figure 16) in the direction indicated, and install the belt onto the PTO pulley as shown in the rear mower deck brackets (B), and secure each end of the way and slide the mower deck under each with a washer and hairpin clip (A). A tions,... side shown, left side same) 5. r n Important: Be sure the belt is installed properly onto all moving parts to its lowest position (see C Cutting Height Adjustment). B 3. t fo ctioC A B o u Figure 18. Lower the mower deck to stop. 2. Adjustments and Service Installation 1. Insert the rear lift ...
Operater's Manual
Page 26
...With parking brake engaged, PTO disengaged and an operator in period and then after performing the adjustment procedure. Check the mower blade stopping time. The mower blades and mower drive belt should come to a complete stop within 5 seconds after electric PTO switch is an acceptable condition. 6. Adjust PTO Clutch... only with engine stopped, key removed and rider on component parts, and is turned off . 26 www.Snapper.com fo tio 1. Check Mower Blade Stopping Time Mower blades and mower drive belt should come to stop within 5 seconds, see an authorized dealer. 5.
...With parking brake engaged, PTO disengaged and an operator in period and then after performing the adjustment procedure. Check the mower blade stopping time. The mower blades and mower drive belt should come to a complete stop within 5 seconds after electric PTO switch is an acceptable condition. 6. Adjust PTO Clutch... only with engine stopped, key removed and rider on component parts, and is turned off . 26 www.Snapper.com fo tio 1. Check Mower Blade Stopping Time Mower blades and mower drive belt should come to stop within 5 seconds, see an authorized dealer. 5.
Operater's Manual
Page 29
...the unit at the points shown in Figure 29, as well as the others have grease fittings above the mower deck, while others listed in this section. Keep oil and grease N d off belts and pulleys. Not all moving parts when grease fittings are compatible. r n Oil: fo tio •... after lubrication. Grease: • front caster wheel axles 2x • front caster spindle bosses • front axle center pivot • mower blade spindles * • mower deck idler arm • mower deck lift motor screw (located up under 2x right fender) Use grease fittings when present.
...the unit at the points shown in Figure 29, as well as the others have grease fittings above the mower deck, while others listed in this section. Keep oil and grease N d off belts and pulleys. Not all moving parts when grease fittings are compatible. r n Oil: fo tio •... after lubrication. Grease: • front caster wheel axles 2x • front caster spindle bosses • front axle center pivot • mower blade spindles * • mower deck idler arm • mower deck lift motor screw (located up under 2x right fender) Use grease fittings when present.
Operater's Manual
Page 32
.... Set engine speed control to FAST. See authorized service dealer. See Servicing the Mower Blades. Bent or rough pulleys. See authorized service dealer. Mower drive belt broken. See authorized service dealer. 32 www.Snapper.com Rider steers or handles poorly. Belt stretched or worn. Engine stalls easily with discharge pointing toward previously cut is rough...
.... Set engine speed control to FAST. See authorized service dealer. See Servicing the Mower Blades. Bent or rough pulleys. See authorized service dealer. Mower drive belt broken. See authorized service dealer. 32 www.Snapper.com Rider steers or handles poorly. Belt stretched or worn. Engine stalls easily with discharge pointing toward previously cut is rough...