Jenn-Air JGRP636H Support and Manuals
Get Help and Manuals for this Jenn-Air item
View All Support Options Below
Free Jenn-Air JGRP636H manuals!
Problems with Jenn-Air JGRP636H?
Ask a Question
Free Jenn-Air JGRP636H manuals!
Problems with Jenn-Air JGRP636H?
Ask a Question
Popular Jenn-Air JGRP636H Manual Pages
Owners Manual - Page 4
... of the range unless specifically recommended in burns from steam. SAVE THESE INSTRUCTIONS
4 Anti-Tip Bracket
Range Foot
To verify the anti-tip bracket is installed and engaged: • Slide range forward. • Look for details. THIS RANGE IS PROVIDED WITH WHEELS TO FACILITATE MOVEMENT. Do not repair or replace any part of the oven. I WARNING...
Owners Manual - Page 33
... button to blink before turning to the "Knob Combinations" chart. Set the Cooktop Control to HI, MED, or LO, depending upon the type of the material that may have followed the instructions for the function you avoid a service call an electrician. See the Installation Instructions for disabling. Make sure you have been converted improperly. See...
Internet Connectivity Guide - Page 1
...W11184746A Internet Connectivity Guide Guide de connexion Internet
Get the App and Get Connected
There are unsure of your router's capablilities, refer to the router manufacturer's instructions.
■■.... NOTE: For 48" models, only one set up a user account. www.jennair.com/connect
In Canada, visit www.jennair.ca
IMPORTANT: Proper installation of Service available at 1-800-JENNAIR ...
Installation Instructions - Page 5
... local codes and...Settings on Surface Burner for Natural Gas" section (page 28) for Natural Gas Operation.
5 Refer to subfloor. Parts Supplied Check that all parts are available from your local hardware store. See the "Install Anti-Tip Bracket" section. ■ Burner grates ■ Burner caps ■ Griddle drip tray (on griddle models)
Parts Needed
■ All models must be installed...
Installation Instructions - Page 7
... above the cooking surface, follow the range hood or microwave hood combination installation instructions for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth, and 36" (91.4 cm) countertop height.
Model/serial/rating plate location/SAID label
NOTE: When installed in order to ensure a flush fit to side wall or other combustible...
Installation Instructions - Page 10
... packaging
A
NOTE: This support is used only for shipping and is off the pallet until range is not needed for installation.
3. Using two or more people to avoid damaging floor. Set range on top of cardboard from top of oven. Failure to avoid scratching.
10 Lay a piece of the
unit. INSTALLATION INSTRUCTIONS
WARNING
Unpack the...
Installation Instructions - Page 14
... installed. 1. This sparking continues until it may take longer. NOTE: Flame heights are factory set to OFF. If they don't appear correct, please contact your dealer or authorized service company...burner caps are properly positioned on griddle models)
The griddle is turned to any position, the system creates a spark to the Use and Care Guide. Griddle
2. Leveling rods can be adjusted...
Installation Instructions - Page 17
...(14" [35.6 cm] WCP)
The range and its individual manual shut-off valve during any pressure testing of the gas supply piping ...model/serial/rating plate. Kick plate slot
2.
Test the gas pressure regulator and gas supply line. Line pressure testing above the set...valve must be checked at test pressures in order to remove or replace kick plate. A
A. Line pressure testing at 1/2 psi (3.5 ...
Installation Instructions - Page 22
...the gas orifice spud in plastic parts bag for illustration.
13. Set gas orifice spud aside. Replace oven bake burner electrode inside bracket....Install the Number 125 oven bake burner orifice spud.
9. Oven bake burner electrode bracket
12. 6. Pull electrode out of a 1/4" (6.4 mm) nut driver to the end of bracket.
10.
Bracket
7.
Grasp electrode here. Insert nut driver...
Installation Instructions - Page 23
...burner orifice hole
4. Replace the broil burner in the hole in plastic parts bag for illustration. Broil burner C. Set aside with the hole...driver to slide shoulder screws into the narrow ends of oven
3. B
C A. Cover notches (4) B. Insert nut driver into place. The screw is aligned with side igniter positioned on 48" [121.9 cm] models)
1. Replace Oven Bake Burner Cover
1. Install...
Installation Instructions - Page 27
... "NAT" are installed, remove them. 2.
Set gas orifice spud aside.
...nut driver to cooktop, do not over the gas pressure regulator cap, and reinstall on the model/serial...manual shut-off valve must be disconnected from the gas supply piping system by first removing (2) T-20 screws. Replace burner cap. 9. If the burner grates are visible.
Line pressure testing above the set...
Installation Instructions - Page 33
... door. B. Insert nut driver into the gas opening, and press down in plastic parts bag for illustration. A
A. Bake burner cover
4. Gas orifice studs are stamped with the hole when a click sounds.
33 Install the Number 148 oven broil burner orifice spud.
5. Lift up and remove oven bake burner cover, and set aside. Remove the...
Owners Manual 1 - Page 4
...: NEVER use a towel or other servicing should never be worn while using the range, follow these instructions can tip the range and be referred to
persons, or damage when using the range. Do not repair or replace any slots, holes or passages in the manual.
I WARNING: NEVER cover any part of the oven. During and after...
Owners Manual 1 - Page 17
... opened . NOTE: Valid only in a bake setting until Sabbath Mode is exited.
The control is... OVEN
Wi-Fi Connectivity and Remote Operation
Models are double ovens, both ovens will be...selections that allows the unit to be scanned or manually added.
Sabbath Mode
■■ Sabbath Mode....
Reference the "Internet Connectivity Guide" for the SAID code on the lower right of...
Owners Manual 1 - Page 33
.../ or noisy. The burner is not set to a proper temperature setting.
A Delay Start has been set to the "Warranty," or visit https://jennair.custhelp.com. On some models, the Sabbath Mode is not set correctly. The temperature knob is set correctly. SOLUTION Replace the fuse or reset the circuit breaker. If the problem continues, call , refer to the...
Jenn-Air JGRP636H Reviews
We have not received any reviews for Jenn-Air yet.